The
aim of surveying is to make plans and maps to show various objects on
the ground at their relative position to suitable scale. Various steps
involved in making the plans is explained below.
Mapping Methods in surveying:
After
completing field work in chain survey and compass survey lot of office
work is involved to prepare the plan (map) of the area surveyed. In
plane table survey office work is less. The office work involved consist
of:
1. Applying necessary corrections to measurements
2. Drawing index plan
3. Selecting scale
4. Selecting orientation
5. Drawing network of survey lines
6. Distributing closing error
7. Filling in the details
8. Colouring the map
9. Drawing graphical scale
10. Writing index.
1. Applying Necessary Corrections to Measurements
Necessary
tape and chain corrections and corrections for local attraction in case
of compass survey, should be applied to the survey lines measured.
2. Drawing Index Plan
On
a rough sheet index plan also known as key plan is drawn. This need not
be to the scale but distances and directions of network of survey lines
should be approximately to a scale. This plan is necessary to identify
the shape of the area to be plotted.
3. Selecting Scale
Depending
upon the type of survey, scale should be selected. In general, scale
selected should be as large as possible, if a range of scale is
recommended. It depends upon the size of the paper as well as largest
linear measurement in the field.
4. Selecting Orientation
Looking
at index plan, orientation of map is to be decided so that the map is
placed in the middle of the drawing sheet with its larger dimension
approximately along the length of paper. North direction is selected and
marked.
5. Drawing Network of Survey Lines
Studying
index map and orientation of paper, first station point of survey is
marked. Starting from here one by one survey line is drawn to the scale
in its direction. After drawing all survey lines, it is clearly seen
whether the selected scale and orientation appropriate. If necessary
they may be changed and network of survey lines is redrawn.
6. Distributing Closing Error
Sometimes
in closed traverse, the last point may not coincide with the plotted
position of first point. The difference between the plotted position is
known as closing error. Before adjusting closing error it is necessary
that there are no plotting errors. If it is due to field work error and
the error is reasonably small it can be adjusted in the office. If error
is large, one has to go back to the field and check doubtful
measurements. In the office closing error is adjusted distributing it
suitably to all lines graphically or by mathematical calculation of
corrected coordinates of station points. After adjusting closing error
network of survey lines are drawn as per the convention.
7. Filling in the Details
Surveyor
has to go through details of one by one survey lines. One by one point
of object noted in the field is marked on the drawing sheet by
converting the change and offsets to the scale. Main scale and offset
scales will be quite useful for this work. After marking the salient
points of the objects like building, boundary lines, roads, culvert
ends, trees, electric poles etc. the respective lines are joined to mark
the object. The field book will be useful in identifying the objects.
If the object is building, the measurements may be only for salient
points near the survey lines looking at overall dimensions of the
building and scaling down, complete building may be shown in the plan.
Thus attending to the field observations of each survey lines all
details may be shown. Standard conventions should be used in showing the
objects.
8. Colouring the Map
If coloured maps are to be made, the recommended light washes of standard shades as listed is IS 962- 1989 may be applied.
9. Drawing Graphical Scale
As
the drawing sheet may shrink and the measurement taken from shrunk
sheet may mislead the distances between any two objects on the map, it
is necessary to draw a graphical scale of 150 to 270 mm long just over
the space for indexing the drawing, which is right hand side lower
corner of the sheet.
10. Writing Index
Index is the
details giving the description of the area plotted, scale used, name of
leader of survey party and the person drawing the plan/map. etc. It is
normally written in the right hand side lower corner of the drawing
sheet. North direction is shown neatly at the right hand side top
corner.
No comments:
Post a Comment